RCD Power Cords
8
configurations
Not sure which cord you need?
Answer a few quick questions and we’ll narrow it down for you.
In stock (17)250 voltsComponent ApprovalsRoHSColor — Black
Length — 2.5 meters
Made to orderColor — Black
Length — 2.5 meters
Made to orderColor — Black
Length — 2.5 meters
Made to orderColor — Black
Length — 2.5 meters
Made to orderColor — Black
Length — 2.5 meters
Made to order250 voltsComponent ApprovalsRoHSColor — Black
Length — 2.5 meters
Made to order250 voltsComponent ApprovalsRoHSColor — Black
Length — 2.5 meters
Made to order250 voltsComponent ApprovalsRoHSColor — Black
Length — 2.5 meters
About RCD Power Cords
The Residual Current Device is used in conjunction with power supply cords to monitor the current of incoming electricity. The RCD is similar to the GFCI, as it monitors any leakage of current and then interrupts the power supply if there is a difference between the line(incoming) current and load (out going) current. The GFCI is more universally used as a protection device, however the RCD is still used in European Countries.
The plugs and connectors in this collection
What each end is, what it mates with, and where to find every cord built on it.
Connector · IEC 60320
IEC 60320 C13
- 15 Amps
- 125/250V
On 6 of the cords here (38%)
The IEC 60320 C13 is a grounded 3 Wire connector rated up to 250V and 15 Amps. The C13 mates with a C14 inlet, and is commonly used in a jumper cable scenario in IT Installations providing power from a PDU to a server, router, switch or other computing device. Most people know the C13 as 'the thing that plugs into my computer' because it is the standard connector used to power most desktop computers. In a desktop computer application, the most common cable is the NEMA 5-15P to C13, which connects your standard North American wall outlet to a desktop computer.
Mates with IEC 60320 C14 Inlet
Plug · International
European Schuko CEE7/7 - Straight
- 16 Amps
- 250 volts
On 6 of the cords here (38%)
The plug (MALE) is a Type F Schuko CEE7/7. It fits both E (France) and F (European / Germany) type outlets (sockets). Available in straight or down/up angle orientation. The plug has two round pins (line and neutral) each 4.8 mm diameter, 19 mm long and spaced 19 mm apart. The plug also has two flat areas (top and bottom sides) and a female contact for the ground.
Mates with Schuko CEE7/7 Outlet
Plug · International
European Schuko CEE7/7 - Down Angle
- 16 Amps
- 250 volts
On 6 of the cords here (38%)
The plug (MALE) is a Type F Schuko CEE7/7. It fits both E (France) and F (European / Germany) type outlets (sockets). Available in straight or down/up angle orientation. The plug has two round pins (line and neutral) each 4.8 mm diameter, 19 mm long and spaced 19 mm apart. The plug also has two flat areas (top and bottom sides) and a female contact for the ground.
Mates with Schuko CEE7/7 Outlet
You are on the European Schuko CEE7/7 - Down Angle family page.
Connector
Europe Schuko CEE7/3 (Female)
- 16 Amps
- 250 volts
On 4 of the cords here (25%)
The connector (FEMALE) is a Type F Schuko CEE7/3 which accepts the Type F Schuko CEE7/7 plug.
For use in international projects in Europe, Germany, Algeria, Austria, Azerbaijan, Belarus, Belgium, Bosnia and Herzegovina, Brunei, Bulgaria, Burundi, Cameroon, Cape Verde, Central Africa Rep, Chad, Comoros, Congo Democratic Republic, Croatia, Czech Republic, Djibouti, Egypt, Eritrea, Finland, France, French Guiana, Gabon, Georgia, Germany, Greece, Greenland, Guadeloupe, Guinea, Guinea-Bissau, Hungary, Iceland, Indonesia, Jordan, Kazakhstan, South Korea, Kyrgyzstan, Liechtenstein, Luxembourg, Macedonia, Madagascar, Mali, Martinique, Monaco, Montserrat, Morocco, Mozambique, Netherlands, Netherlands Antilles, New Caledonia, Norway, Philippines, Portugal, Reunion, Romania, Russia, San Marino, Senegal, Serbia and Montenegro, Slovenia, Spain, Suriname, Sweden, Syria, Togo, Tunisia, Turkey, Ukraine, Vietnam.Mates with Schuko CEE7/7 Inlet/Plug
Plug · International
Italy CEI 23-50 3-Pin 10A
- 10 Amps
- 250 volts
On 4 of the cords here (25%)
The CEI 23-50 10A plug type configuration is rated for 250VAC and 10 Amps in Italy and is also classified as the international type L plug. The 10A configuration is smaller than the 16 amp configuration to prevent connection the 16 amp plug type into a 10 amp receptacle, which is an electrical hazard.
You are on the Italy CEI 23-50 3-Pin 10A family page.
About RCD Power Cords
World Cord Sets supplies rcd power cords from our East Windsor, Connecticut headquarters, with manufacturing across US and overseas facilities. Cords are tested and certified to spec before shipment. We stock 8+ configurations and build custom cords to order — hand-terminated builds from in-stock components typically ship in 3–4 business days. In-stock orders placed by 2:30 PM ET ship the same day from our Connecticut warehouse.
Current rating
10 Amps
Voltage rating
250 volts
Certifications & compliance
- Component Approvals
- RoHS
- Every cord we build is hi-pot tested
- Same-day shipping by 2:30 PM ET
- NET 30/60/90 for approved accounts
- In-house engineering and compliance support
Frequently asked questions
- What certifications do these power cords carry?
- UL and cUL-listed cord sets across the catalog, with 30+ international approval marks (VDE, ENEC, PSE, SAA, CCC, KC and more) on country-specific cords. The approvals each part carries are listed on its product page; documentation is available from sales.
- Do you require a minimum order quantity?
- No. We sell from 1 cord to 100,000. Volume discounts apply automatically at quantity breaks — you'll see pricing tiers on every product page.
- Can I get a custom length or color?
- Yes. Custom lengths and non-standard colors are hand-terminated in our Connecticut shop — typically 3–4 business days from in-stock components. Call (860) 763-2100 or submit a quote request with your specs.
- How fast does this ship?
- In-stock orders placed by 2:30 PM ET ship the same day via FedEx or UPS. All standard configurations are stocked in East Windsor, CT.